Useful information on how to set up your robot vacuum cleaner - overview of functions and preparation for use

Setting up a robot vacuum cleaner is a way to automate cleaning in an apartment. Like any other technique, the robot vacuum cleaner consumes electricity and water.

If it works for a long time without cleaning, it may burn out. To extend the life of the device, it needs to dry clean at least once a week and wet clean once a month.

Before you start cleaning, the vacuum cleaner must be set up. Each device has its own parameters that must be taken into account when programming it.

What does a robot vacuum cleaner consist of and how to prepare it for work

The Xiaomi robot vacuum cleaner consists of two main parts:

1. Robot module.
2. Control module.

The vacuum cleaner robot module is made in the form of a rectangle with rounded corners, in the upper part, the module has a rectangular hole with a slot in which the fine filter is located.

On the left side of the case there is a waste tray, and on the right side there is a power on/off switch, at the bottom there is a battery compartment.

The control module (Wi-Fi module) has the form of a rectangle with a rounded corner, in its upper and lower parts there are power on and off buttons, the button for turning on the "Turbo" mode, as well as the "Reset" button is located on the underside of the case.

There are 4 touch keys on the robot module, they are used to control the robot vacuum cleaner, namely turning the power on, turning off the power, moving around the room and cleaning the corners. A special sensor captures objects that are at floor level and does not allow the robot to pass them.

The system then starts looking for a lower level where he can park. The kit comes with two filters - one for collecting debris, and the second for air purification.

On the back panel there is a switch for selecting the type of cleaning: automatic and manual. It serves to turn on the robot vacuum cleaner. Power button on the side on the right side. Also, if you press it several times, the automatic cleaning mode is activated.

How to prepare the robot vacuum cleaner for work

• Check that the battery is charged.
• Clean the soleplate from food debris, dust and dirt.
• Turn off the appliance and let it cool down before removing the new coating.
• Empty the dust bin and waste container.
• Turn on the robot.
• Wait until fully charged.
• Set the cleaning time, speed and direction of movement.
• After cleaning, turn off the device and wait until it is completely discharged.
• Disconnect the appliance from the mains and rinse all parts under running clean water.
• Wipe the vacuum cleaner with a soft cloth and leave to dry in a well-ventilated area.
• Don't forget to reinstall the parts.
• Check the correct operation of the device.
• Recharge the device.

Preparing the apartment for cleaning with a robot vacuum cleaner

You need to prepare the apartment for cleaning with a robot vacuum cleaner in advance. First of all, you need to remove all foreign objects from the room that may prevent the robot from cleaning the surface. It is necessary to remove everything that may prevent the robot vacuum cleaner from reaching the cleaning site.

After all these items are removed, you should turn on the robot. Next, the robot vacuum cleaner will clean.

wires

For a more thorough cleaning, remove all wires. This is also necessary so that the robot does not get entangled in them. It is necessary to thoroughly wipe the floor before cleaning. The robot vacuum cleaner must not leave any traces of dirt behind.

wet trash

Wet debris should be removed before cleaning with a wet cloth or napkin. If you remove it with a damp sponge, it may get wet, and this will prevent the robot from working effectively. When cleaning, do not forget that water does not get inside the robot vacuum cleaner.

Cleaning under furniture

In order for the robot to get into hard-to-reach places, you need to move the furniture. Then you should turn on the robot and clean up. Do not forget about hard-to-reach places.

Large trash

Cleaning large debris before cleaning with the robot cleaner is necessary in order to collect large debris such as paper, pieces of cloth, glass fragments, and so on. Large debris can clog the nozzle of the robot cleaner, making it difficult to clean.

Overcoming obstacles with a robot vacuum cleaner

Before cleaning, the robot vacuum cleaner must walk around the perimeter of the room. This will allow him to see what obstacles he may encounter along the way. Depending on the size of the room, the robot will determine how long it will take to clean. If possible, it is better to remove large objects from the floor in advance. So the work of the robot will be more efficient.

Functions of the robot vacuum cleaner

1. Scheduled cleaning

With the help of a "smart" schedule, you can set regular cleaning, which will take place every day at a strictly defined time. With this function, you can independently set the start time of the robot vacuum cleaner, and also set the time interval during which he must be near the wall (to bypass obstacles).

2. Dry cleaning

The robot vacuum cleaner can be used to pick up small debris (dust, pet hair, crumbs, small stones, etc.) and dry cleaning. This greatly improves the efficiency of the device.

3. Wet cleaning

This method of cleaning allows you to more thoroughly clean the surface from dirt, dust and pet hair. When the robot finishes wet cleaning, it returns to the base to charge the battery.

4. Intensive cleaning

In the case when it is necessary to quickly remove a lot of debris in a small area, the intensive cleaning mode is used. It allows you to work without interruption for 15 minutes. In rest mode, the duration of work does not exceed 3 minutes.

Be sure to open the trash cover while the machine is in operation. This will prevent debris from getting stuck in the vacuum cleaner during cleaning and prolong its life.

5. Cleaning along the walls

The function of bypassing obstacles in the form of walls or furniture provides effective removal of dirt from the walls and corners of the room. In addition, the vacuum cleaner independently determines the boundaries of the working area.

To prevent injury, the device is equipped with a built-in laser height sensor that always keeps a distance from the floor surface.The device is controlled using the touch panel on the case or via a smartphone application.

6. Virtual wall

The presence of this function allows you to avoid the fall of the robot from a height when cleaning. This is achieved by the fact that before each cleaning cycle, the device creates a virtual wall behind itself.

7. Building a floor plan

The room plan is necessary to draw up the shortest routes around obstacles. After analyzing the layout of the room, the robot vacuum cleaner develops a route to overtake the obstacle, as well as the trajectory of movement at the point "at the junction" of the premises. Based on the developed room plan, the program generates a three-dimensional model of the room.

8. Return to charge

If necessary, the robot vacuum cleaner returns to the charging station, where it can charge itself. Smart robotic vacuum cleaners work on the principle of a closed cycle, due to which it takes about 2 hours to fully charge the machine's battery.

9. Determination of the minimum amount of dust

When the room becomes too dirty, the robot cleaner starts working at a higher intensity. It works continuously and collects dust from the floor surface.

By measuring the amount of dust collected, you can understand when the robot cleaner needs to pause and change direction or even stop.

10. Cleanliness control

The device is able to determine the cleanliness of the room and proceed to the next stage of cleaning. In case of contamination, it automatically turns off. The device not only cleans the floors, but also works as a smart vacuum cleaner. It can be switched on for cleaning carpets or cleaning furniture.

The ability to control the vacuum cleaner from a smartphone

The vacuum cleaner can be connected to a smartphone and controlled remotely directly from your phone.

To do this, you need to download a special application on a phone that supports wireless technologies. Then connect your vacuum cleaner to Wi-Fi. In the application, you can configure the vacuum cleaner so that it does not just clean rooms, but itself searches for pollution that needs to be dealt with.

For example, if you decide that there is dust in the living room and crumbs in the kitchen, you can set the cleaning so that the vacuum cleaner itself moves around the rooms and cleans them. And if on the way it comes across garbage, it will return to the place where the garbage is located.

In addition, the same application provides the function of automatic cleaning of the entire apartment. That is, the vacuum cleaner itself returns to where it recently cleaned. This program is very convenient.

The application also provides the ability to call for help from other users, for example, when there is no way to approach the vacuum cleaner, or it is broken.

Vacuum Cleaner Care

The care of the robot vacuum cleaner must be inspired by its owner. First of all, it is necessary to clean the filter located in the garbage collection tank. This procedure must be performed at least once a week.

You should also regularly clean the dust container, which must be disassembled and rinsed thoroughly. This will prevent dust and dirt from entering the battery.

It should be remembered that the robot vacuum cleaner is an autonomous device and it is able to keep the floor clean on its own. Vacuum cleaner care includes cleaning all interchangeable nozzles, filters and other accessories. To facilitate this procedure, you can use special cleaning products.

Problems and Troubleshooting

Even the highest quality robot vacuum cleaner may experience the following problems during long-term operation.

Problem 1. The robot does not detect obstacles in the form of curtains, curtains, walls, etc. In fact, robot vacuums do an excellent job of this task. In this case, you need to check to fix the motion sensor - this may be due to poor contact of the sensor. If this does not happen, then the matter is in the settings.

Problem 2 The robot does not find the charging cable or docking station. In this case, you need to check the connection of the charger and the robot, as well as the charging of the robot itself. If the charger is connected correctly, then you need to check the connection of the docking station.

Problem 3. The vacuum cleaner does not start after charging is completed. It is necessary to wait until the robot vacuum cleaner is completely disconnected from the docking station, then plug it into the outlet and start it with the button.

Problem 4. The robot does not move, does not clean, does not change direction. To get rid of this problem, you need to clean and lubricate the brushes, check if the shock sensor is working and replace the control unit.

Useful video

From this video you will learn how easy it is to set up a robot vacuum cleaner: